Equipment Overview& Equipment Details
Equipment Details
Make, Model & Classification
| Name | Baler: Hydraulic |
| Model | Mil-tek Model H500 |
| Classification | Baling |
Operations
| Description or Purpose | For the baling of cardboard, plastic film and other compactable recyclables. |
| Operating Principles | Simple drop door design allows for use in tighter locations. Feed in large volumes of material with each loading, no need to wait once filled, walk away as the machine goes through its pressing cycle unattended. Two bale tie options, bale banding, or preformed "reef knot" ended "Easyloop" wires for wire tie off. Bale out is mechanically assisted onto a pallet or trolley. |
| Additional Information | The H500 is a industrial scale baler making a mill sized bale tradable on the commodity market. It is a very versatile machine, utilised for a variety of baled materials. German engineered and built, with ultimate durability. Fully serviced by Mil-tek technicians in most areas. |
Photograph
Recyclables Processed & Productivity
Recyclables Processed
Target Recyclables and Productivity Rates
| Recyclable Type | Productivity - Loading Rate (kg per hour) |
Processing Capacity - Treatment (kg per week) |
Storage Capacity (kg per batch) |
Operating Life (machine hrs) |
|
|---|---|---|---|---|---|
|
Food Organics | ||||
|
|
Other Organics (garden etc.) | ||||
|
Flexible Plastic | 900 | - | - | - |
|
|
Rigid Plastic | 500 | - | - | - |
|
|
Mixed Plastics | 900 | - | - | - |
|
|
Expanded Polystyrene | - | - | - | - |
|
|
Glass | ||||
|
|
Paper | 900 | - | - | - |
|
|
Cardboard | 700 | - | - | - |
|
|
Mixed Paper & Cardboard | 800 | - | - | - |
|
|
Timber | ||||
|
|
Other Recyclable | ||||
| If Other | PVC, eWaste, Bulkabags | ||||
Productivity
Life Expectancy
| Operating Life - Years | 15 |
Level of Automation
| Operating Mode | Batch |
| Degree of Automation | Other |
| If Other (specify) | Attendance only to bale out. 5 minute process, usually less than once per day. |
Labour Requirements
| Number of Operators | 1 |
| Operator Time (per cycle in mins.) |
0 |
Consumables Required
| Consumables | Bale banding or wire Easyloops |
Service Requirements
| Service Freq. (Tonnes) | 0 |
| Service Freq. (Months) | 12 |
| Downtime per Service (hours) | 2 |
Periodic Cleaning Requirements
| Periodic Cleaning | Dependent on material compressed. Recommend weekly wipe down to extend equipment life. |
Loading & Unloading Equipment
| Manual Handling Loading | Manual |
| Manual Handling Unloading | Mechanical Loader |
Work Health and Safety & Permitting
Work Health and Safety
Training
| Operator Training Requirements | Familiarisation induction - by OEM/supplier |
Personal Protective Equipment
|
|
Head - Hard Hat |
|
|
Eyes - Glasses |
|
|
Breathing - Mask or Respirator |
|
|
Hands - Gloves |
|
|
Feet - Industrial Footwear |
|
|
Visibility - Hi-viz Clothing |
|
|
Other PPE |
Training Material
|
|
Printed |
|
|
Video/DVD |
|
|
Web-based |
|
|
Other |
Fencing & Enclosures
|
|
Fencing |
|
|
Bunding |
|
|
Floor Reinforcing |
|
|
Covers or Shielding |
|
|
Other |
Approvals Related to Use of Output
Important Note on Composting in NSW
In NSW, applying waste to land – including a processed waste such as compost - or using it as a fuel may trigger various regulatory requirements. Depending on the proposed use you may be required to comply with a Resource Recovery Exemption or need to hold an environment protection licence, and pay the waste levy.
While there is a Compost Exemption (2014) it is important to note that drying or dehydrating food waste, or any other compostable waste, is specifically excluded from consideration under this exemption. Drying or dehydrating equipment uses externally supplied energy to heat and ventilate food waste or any other compostable waste in order to rapidly dry the waste material over a short time period (typically 24 to 48 hours), either with or without the addition of an inoculum. If you are interested in this type of equipment you should refer to the resource recovery exemptions for information on lawful use of outputs.
If it is intended to use the material as a fuel, it must comply with the NSW Energy from Waste Policy Statement. http://www.epa.nsw.gov.au/waste/140056enfromwasteps.htm
Installation Specifications
Installation Specifications
Utilities
|
|
Power | 415 Volts | 7.5 kWh |
|
|
Water | KPa | - l/min |
|
|
Sewer | - l/min | |
|
|
Compressed Air | 6-8 KPa | 90 CuM/min |
|
|
Gas | - Kjoule/hr |
Dimensions
| Length | 130 cm |
| Width | 160 cm |
| Height | 310 cm |
| Footprint | 2.1 sq.m |
| Weight | 2050 kg |
| Lateral clearance | 10 cm |
| Overhead clearance | 5 cm |
Service Offering
|
|
Supply |
|
|
Installation |
|
|
Maintenance |
|
|
Product Uplift |
|
|
Training |
|
|
Other |
| If Other |
In-Feed & Out-Feed Characteristics
In-Feed Characteristics
Acceptable In-feed Characteristics
|
|
Loose |
|
|
Bundled |
|
|
Tied |
|
|
Wet |
|
|
Dry |
|
|
Shredded |
|
|
Lightly Soiled |
|
|
Heavily Soiled |
|
|
Other |
| If Other | 0 |
Exclusions
| Excluded Materials | Aerosols cans, lidded cans, explosives canisters |
Out-Feed Characteristics
Out-feed Product Characteristics - Shape
|
|
Rectangular Prism |
|
|
Cylindrical |
|
|
Other |
Out-feed Product Characteristics - Container
|
|
Bag/Sack |
|
|
Wrapped |
|
|
Bin |
|
|
Other |
Out-feed Dimensions
| Length | 80 cm |
| Width | 120 cm |
| Height | 80 cm |
| Footprint | 1 sq.m |
| Weight | 350-450 kg |
| SG | - specific gravity |
| Density | 586 kg/Cu.m |
| By-product and Wastes | NIL |
Amenity and Nuisance Issues
|
|
Noise |
|
|
Odour |
|
|
Vibration |
|
|
Light |
|
|
Heat |
|
|
Other |
Market/Recipients
|
|
Reprocessor |
|
|
End Market |
|
|
Other |
OEM & Supplier Information
OEM & Supplier Information
OEM Company Details
| Company Name | Mil-tek Waste Solutions |
| Postal Address | 3 Tindal Rd, Tuggerah |
| State | NSW |
| Country | Australia |
| Postcode | 2259 |
| Web Site | www.miltek.com.au |
| Contact Name | Jason Campbell |
| Contact Telephone | 0476 508 500 |
| Contact Email | jason.campbell@miltek.com.au |
Supplier Company Details
| Company Name | Mil-tek Waste Solutions |
| Postal Address | 3 Tindal Rd, Tuggerah |
| State | NSW |
| Country | Australia |
| Postcode | 2259 |
| Web Site | www.miltek.com.au |
| Contact Name | Jason Campbell |
| Contact Telephone | 0476 508 500 |
| Contact Email | jason.campbell@miltek.com.au |
